(2023) PASS NACE-CIP2-001 exam with NACE NACE-CIP2-001 Real Exam Questions
Real exam questions are provided for CIP Level 2 tests, which can make sure you 100% pass
NEW QUESTION 32
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. inorganic zincs.
- B. powder coatings.
- C. epoxies.
- D. urethanes.
Answer: A
NEW QUESTION 33
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise your QC Manager to change the ITP to the use of the salt smart meter
- B. Review the specification with the other inspector to see what method was specified
- C. Redo the pre-cleaning based on the other inspectors results
- D. Advise the other inspector he is using an incorrect method
Answer: B
NEW QUESTION 34
Corrosion is the reverse process of
- A. steel manufacturing.
- B. flaking.
- C. galvanic deterioration.
- D. hot dipping.
Answer: A
NEW QUESTION 35
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. disposed of properly.
- B. washed with clean potable water prior to Use.
- C. run through the air wash separator.
- D. mixed with uncontaminated abrasive
Answer: A
NEW QUESTION 36
In which type of concrete are laitance commonly encountered?
- A. Concrete block (poured with a form)
- B. Glass fiber cement
- C. Gunite
- D. Poured (wet cast)
Answer: D
NEW QUESTION 37
Surface preparation methods for Non-ferrous metals are:
- A. Not required
- B. The same for all Non-FetT0us metals
- C. Specific for each type of Non-ferrous metal
- D. The same as for Ferrous metals
Answer: C
NEW QUESTION 38
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Scarifiers
- B. Power Tools
- C. Water Jetting Equipment
- D. Abrasive Blasting Equipment
Answer: C
NEW QUESTION 39
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A mechanical adhesion tester
- C. A set of 14 pencils of varying hardness
- D. A destructive paint inspection Tooke gauge
Answer: D
NEW QUESTION 40
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION 41
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 single rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 double rubs with a saturated cloth.
- D. 50 double rubs with a saturated cloth.
Answer: D
NEW QUESTION 42
Examples of non-ferrous metals include
Select All that Apply:
- A. aluminum
- B. copper
- C. iron
- D. mild steel.
Answer: A,B
NEW QUESTION 43
Pre-cleaning of work pieces will NOT remove
- A. snow, ice or water.
- B. mill scale.
- C. oil or grease.
- D. dirt.
Answer: B
NEW QUESTION 44
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Request clarification from the specifier
- C. Ignore the additional requirement
- D. Call your supervisor
Answer: A
NEW QUESTION 45
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that are completely different to steel
- C. Methods that have been modified for concrete
- D. Methods that are the same as wood
Answer: C
NEW QUESTION 46
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface profile prior to coating
- B. Compressive and tensile strength prior to coating
- C. Surface cleanliness prior to coating
- D. Contamination levels prior to coating
Answer: A
NEW QUESTION 47
When observing design defects the NACE Inspector should:
- A. Document the defect and the potential problems that could result
- B. Stop the job immediately
- C. Ignore the defect as the inspector can't change the design
- D. Request that the item be rebuilt with a better design for coating
Answer: A
NEW QUESTION 48
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION 49
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Refuse to take readings until an is in place
- B. Call your supervisor
- C. Develop your own methodology and proceed take the readings
- D. Use a generally accepted industry standard and to take readings
Answer: D
NEW QUESTION 50
Ideally, documentation requirements should be defined:
- A. By the inspector
- B. In the specification
- C. By the contractor
- D. At the pre-job conference
Answer: B
NEW QUESTION 51
A reinforced coating is
- A. equally resistant to abrasion and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to movement and impact as a non-reinforced coating.
Answer: C
NEW QUESTION 52
You should bulk store coatings containing isocyanates
- A. in a heated warehouse.
- B. wherever it is convenient
- C. in a well ventilated area separate from the work place.
- D. in a refrigerated warehouses
Answer: C
NEW QUESTION 53
......
Latest NACE-CIP2-001 Pass Guaranteed Exam Dumps Certification Sample Questions: https://www.prep4pass.com/NACE-CIP2-001_exam-braindumps.html
NACE-CIP2-001 Exam with Guarantee Updated 100 Questions: https://drive.google.com/open?id=1K9MqKYxXLWYoRKmTVLDwfVUrXG9vbywn
