Free NACE-CIP2-001 Sample Questions and 100% Cover Real Exam Questions (Updated 100 Questions)
Download Real NACE NACE-CIP2-001 Exam Dumps Test Engine Exam Questions
NEW QUESTION 60
Which is used to calibrate a pH meter?
- A. Deionized water
- B. Standard solvent solution
- C. Standard buffer solution
- D. Distilled water
Answer: C
NEW QUESTION 61
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Coal Tar Enamel
- B. Liquid epoxies
- C. Heat-shrink sleeves
- D. Concrete
Answer: B
NEW QUESTION 62
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Sacking
- B. High-pressure water washing
- C. Acid etching
- D. Stoning
Answer: C
NEW QUESTION 63
An Inspection and Test Plan is required when:
- A. It is always required
- B. When the Inspector requests one
- C. When the Coating Applicator requests one
- D. When the Owner specifies one
Answer: A
NEW QUESTION 64
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Abrasive Blasting Equipment
- B. Scarifiers
- C. Power Tools
- D. Water Jetting Equipment
Answer: D
NEW QUESTION 65
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. inorganic zincs.
- B. powder coatings.
- C. urethanes.
- D. epoxies.
Answer: A
NEW QUESTION 66
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION 67
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It doesn't contain biocide
- D. It contains biocide
Answer: D
NEW QUESTION 68
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION 69
Inspector reports should always be copied to:
- A. All parties involved in the project
- B. The Owner only
- C. Whomever the Owner identifies
- D. The Contractor and Owner
Answer: C
NEW QUESTION 70
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A destructive paint inspection Tooke gauge
- C. A hardness tester
- D. A mechanical adhesion tester
Answer: B
NEW QUESTION 71
NACE International Standards are developed by:
- A. International mandates
- B. Government mandates
- C. Standard committees
- D. Regional mandates
Answer: C
NEW QUESTION 72
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that are the same as wood
- C. Methods that are completely different to steel
- D. Methods that have been modified for concrete
Answer: D
NEW QUESTION 73
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. disposed of properly.
- B. washed with clean potable water prior to Use.
- C. mixed with uncontaminated abrasive
- D. run through the air wash separator.
Answer: A
NEW QUESTION 74
A reinforced coating is
- A. equally resistant to movement and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
Answer: C
NEW QUESTION 75
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. The same as coating steel
- C. More challenging than coating steel
- D. Less challenging, than coating steel
Answer: C
NEW QUESTION 76
......
New NACE-CIP2-001 exam dumps Use Updated NACE Exam: https://www.prep4pass.com/NACE-CIP2-001_exam-braindumps.html
Verified NACE-CIP2-001 Dumps Q&As - NACE-CIP2-001 Test Engine with Correct Answers: https://drive.google.com/open?id=18KCHr-jrbJ4G5jtdePmw9cbbLBcbmT2V
