VALID 350-501 Exam Dumps For Certification Exam Preparation
350-501 Dumps PDF 2023 Strategy Your Preparation Efficiently
NEW QUESTION # 186
Refer to the exhibit. A network engineer observed congestion between routers R1 and R4, which are connected on a point-to-point link. Two servers that reside on networks on R1 and R4 generate heavy traffic between them with most traffic going from R4 to R1. To improve overall performance, the engineer wants to drop inbound packets that exceed a configured threshold, without disrupting traffic that passes from R4 to R3. Which action must the engineer take to resolve the issue?
- A. Implement traffic policing to drop packets that exceed the given threshold.
- B. Implement a service policy in the outbound direction on each interface on the link to tag traffic exiting each router.
- C. Implement FIFO to queue excess traffic for transmission when bandwidth is available.
- D. Implement traffic shaping to drop excess packets.
Answer: A
NEW QUESTION # 187
Refer to the exhibit:
Assume all other configurations are correct and the network is otherwise operating normally. Which conclusion can you draw about the neighbor relationship between routers R1 and R2?
- A. The neighbor relationship is down because R1 believes R2 is in AS 65012.
- B. The neighbor relationship is up
- C. The neighbor relationship will be up only if the two devices have activated the correct neighbor relationships under the IPv4 address family
- D. The neighbor relationship is down because the loco I-as value for R2 is missing in the R1 neighbor statement
Answer: A
NEW QUESTION # 188
Refer to the exhibit:
When implementing an LDP protocol, an engineer experienced an issue between two directly connected routers and noticed that no LDP neighbor exists for 1.1.1.1.
Which factor should be the reason for this situation?
- A. R2 sees the wrong type of hellos from R1
- B. R2 does not see any hellos from R1
- C. LDP needs to be enabled on the R2 loopback interface
- D. LDP needs to be enabled on the R2 physical interface
Answer: D
NEW QUESTION # 189
Refer to the exhibit:
Based on the show/ command output, which result m true after BGP session is established?
- A. No routes are accepted from the neighbor 192.168.2.2, nor are any routes advertised to it
- B. The IOS XR router advertises and accepts all routes to and from eBGP neighbor 192.168.2.2
- C. The IOS XR router does not advertise any routes to the neighbor 192.168.2.2,but it accepts all routes from 192.168.2.2.
- D. The IOS XR router advertises all routes to the neighbor 192.168.2.2, but it does not accept any routes from 192.168.2.2
Answer: A
NEW QUESTION # 190
A network engineer is configuring a BGP route policy for the SUBNET prefix set. Matching traffic must be dropped, and other traffic must have its MED value set to 400 and community 4:400 added to the route. Which configuration must an engineer apply?
- A.
- B.
- C.
- D.
Answer: A
NEW QUESTION # 191
While implementing TTL security, you issue the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command.
After you issue this command, which BGP packets does the PE accept?
- A. to 2.2.2.2, with a TTL of less than 253
- B. from 2.2.2.2, with a TTL of 253 or more
- C. from 2.2.2.2, with a TTL of less than 2
- D. to 2.2.2.2, with a TTL of 2 or more
Answer: B
NEW QUESTION # 192
A customer of an ISP requests support to setup a BGP routing policy. Which BGP attribute should be configured to choose specific BGP speakers as preferred points for the customer AS?
- A. lowest local preference inbound
- B. highest local preference outbound
- C. highest local preference inbound
- D. lowest multi-exit discriminator
Answer: B
Explanation:
Section: Networking
NEW QUESTION # 193
Refer to the exhibit. An engineer is configuring multitiopology IS-IS for IPv6 on router R1. Which additional configuration must be applied to complete the task?
A)
B)
C)
D)
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: B
NEW QUESTION # 194
Refer to the exhibit:
If router A is the RP, which PIM mode can you configure so that devices will send multicast traffic toward the RP?
- A. PI MM-DM
- B. PIM-SM
- C. BIDIR-PIM
- D. PIM-SSM
Answer: C
NEW QUESTION # 195
Refer to the exhibit.
AN engineer is configuring segment routing on an ISP to simplify traffic engineering and management across network domains. What should the engineer do to complete the implementation of segment routing?
- A. Area Authentication must be enable before segment routing will run.
- B. OSPF must be configured with wide area metrics to support routing.
- C. Area authentication must be enable before segment routing will run.
- D. The segment will run without any further configuration.
Answer: C
NEW QUESTION # 196
Refer to the exhibit:
Which purpose of implementing NSF with this configuration is true?
- A. The router uses NSF to handle RP switchover while allowing neighbor relationships to remain up
- B. The router uses NSF to load balance traffic between two links, with the primary link alternating every
90 seconds - C. The router uses NSF to load balance traffic on a routed EtherChannel
- D. The router uses NSF to reduce neighbor-relationship downtime during RP switchover
Answer: A
NEW QUESTION # 197
Which MPLS design attribute can you use to provide Internet access to a major customer through a separate dedicated VPN?
- A. The customer that needs the Internet access service is assigned to the same RTs as the Internet gateway
- B. The Internet gateway inserts the full Internet BGP routing table into the Internet access VPN
- C. The CE router supports VRF-Ute and the full BGP routing table.
- D. The Internet gateway router is connected as a PE router to the MPLS backbone.
Answer: B
NEW QUESTION # 198
Refer to the exhibit. An engineer is preparing to implement data plane security configuration.
Which statement about this configuration is true?
- A. Router 1 is the trigger router in a RTBH implementation.
- B. Router 2 is the router receiving the DDoS attack
- C. Router 2 must configure a route to null 0 for network 192 168.1 0/24 for the RTBH implementation to be complete.
- D. Router 1 must be configured with uRPF for the RTBH implementation to be effective.
Answer: A
NEW QUESTION # 199
Refer to the exhibit.
Refer to the exhibit. A network engineer is implementing multicast Source-A to send a multicast stream for Receiver-A, and multicast Source-B to send a multicast stream for Receiver-B. Router RC forwards the IGMP host a report and leaves messages to IP address 192.168.10.1. How must the multicast features be implemented to prevent RB from receiving multicast flooding from Source-A?
- A. Configure PIM-SSM on RB and RC interface Ge 0/0.
- B. Enable ip pim passive on RB interface Ge0/0.
- C. Change the helper-address value to 192.168.10.2 on RC.
- D. Enable ip pim neighbor-filter on RC interface Ge0/0.
Answer: B
NEW QUESTION # 200
Refer to the exhibit:
Which statement about this configuration is true"?
- A. It requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run
- B. It requires OSPF to also be running to have optimized Cisco MPLS TE tunnels
- C. It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing
- D. It requires an explicit Cisco MPLS TE path to be configured for the tunnel to run
Answer: C
NEW QUESTION # 201
Refer to the exhibit:
Which statement about this configuration is true"?
- A. It requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run
- B. It requires OSPF to also be running to have optimized Cisco MPLS TE tunnels
- C. It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing
- D. It requires an explicit Cisco MPLS TE path to be configured for the tunnel to run
Answer: C
NEW QUESTION # 202 
Refer to the exhibit. You are configuring an administrative domain in the given multi-vendor environment with PIM-SM.
Which feature can you implement so that devices can dynamically learn the RP?
- A. BIDIP-PIM
- B. BSR
- C. Auto-RP
- D. SSM
Answer: C
Explanation:
Section: Services
NEW QUESTION # 203
Refer to me exhibit. An engineer started lo configure a router for OSPF.
Which configuration must me engineer perform on me router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: C
NEW QUESTION # 204
Refer to the exhibit:
Which effect of this configuration is true?
- A. R1 can support a graceful restart operation on the peer, even if graceful restart is disabled on the peer
- B. R1 can failover to any peer
- C. R1 can failover only to a peer that is configured for LDP SSO/NSF
- D. R1 can support a peer that is configured for LDP SSO/NSF as the peer recovers from an outage
Answer: C
NEW QUESTION # 205
Drag and drop the technologies from the left onto the correct definitions on the right.
Answer:
Explanation:
NEW QUESTION # 206
......
Related Certifications
- CCIE Service Provider
Cisco CCIE Service Provider lies at the pinnacle of the Cisco Service Provider certification track and is exactly the step to make after attaining the CCNP Service Provider certificate. It confirms one's expert-level mastery of Service Provider technologies. To qualify for it, you must pass a combination of two exams a core 350-501 test that focuses on the fundamentals of the field and a hands-on lab exam that checks the mastery of the service provider solutions through a practical environment. The lab exam, in this case, is CCIE Service Provider v5.0.
- CCNP Service Provider
Cisco CCNP Service Provider proves your capability to implement service provider solutions. Achieving this certificate requires meticulous mastery of 350-501 exam concepts in addition to passing the concentration test of your liking. That being said, the full list of the concentration options associated with the CCNP Service Provider certification includes the following: Cisco 300-510 Implementing Cisco Service Provider Advanced Routing Solutions (SPRI), Cisco 300-515: Implementing Cisco Service Provider VPN Services (SPVI), Cisco 300-535: Implementing Automation for Cisco Service Provider Solutions (SPAUTO).
- Cisco Certified Specialist – Service Provider Core
Cisco Certified Specialist – Service Provider Core is a creation of the new Cisco curriculum which states that every professional-level exam now earns the candidates a Specialist title alongside the accreditation they are going to obtain. In a nutshell, this is a deserved recognition for your accomplishments at the professional level regardless of your further path.
Latest Verified & Correct 350-501 Questions: https://www.prep4pass.com/350-501_exam-braindumps.html
100% Pass Guaranteed Download CCNP Service Provider Exam PDF Q&A: https://drive.google.com/open?id=1OSERZvGK47IXg8JW3rzs5iiJrFd4mycx
