Free Nov-2023 UPDATED NACE NACE-CIP1-001 Exam Questions & Answer
Latest Success Metrics For Actual NACE-CIP1-001 Exam Realistic Dumps
NEW QUESTION # 38
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Read the manufactures' instructions
- C. Ensure the instrument is within calibration parameters
- D. a), b) & c)
Answer: D
NEW QUESTION # 39
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Call your supervisor
- C. Permit coating to take place so as not to lose the blast
- D. Review the relevant standard with the Contractor
Answer: D
NEW QUESTION # 40
Which one of the following documents is the best source for coating technical data:
- A. Specification
- B. Application Guidelines
- C. Safety Data Sheet;
- D. Technical Data Sheet
Answer: D
NEW QUESTION # 41
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Hire a third patty to assist you in understanding the document
- C. Advise the owners' representative of your lack of knowledge in this area
- D. Carefully review the document and do the best you can
Answer: D
NEW QUESTION # 42
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 100% of the specified maximum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: A
NEW QUESTION # 43
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Measuring ditty, tacky, or soft films
- B. Rotating the dial too fast when taking measurements
- C. Taking measurements too far from the edge of a surface
- D. Failing to determine the base metal reading (BMR)
Answer: A,B,D
NEW QUESTION # 44
Digital hygrometers
- A. consist of a bimetallic sensing element protected from wind gusts.
- B. are used to measure temperature from a distance.
- C. use a thermocouple in contact with the surface to measure temperature
- D. determine relative humidity, air temperature, and dew point temperature:
Answer: D
NEW QUESTION # 45
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 75 Gauge Readings resulting in 25 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
Answer: D
NEW QUESTION # 46
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To make the coating flow out better
- C. To control the evaporation rate
- D. To dissolve the resin
Answer: C
NEW QUESTION # 47
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Skip the checks and just record the same readings as you have been getting
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks and consult the Owner's representative for direction
Answer: D
NEW QUESTION # 48
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- C. Document the problem and advise the Contractor
- D. Break the blisters to see what's inside
Answer: A
NEW QUESTION # 49
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION # 50
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. develops a polished surface, which is a poor anchor profile for most coatings
- B. scratches the surface too deeply resulting in uneven coating application
- C. damages structural elements thereby speeding up the corrosion process.
- D. develops a good anchor profile resulting in uneven coating application.
Answer: A
NEW QUESTION # 51
Osmotic blistering is most likely to occur as a result of
- A. airless spray application
- B. overcoating a surface contaminated with chemical salts.
- C. inadequate anchor pattern/surface profile.
- D. applying tine coating too thin.
Answer: A
NEW QUESTION # 52
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. A coating layer applied to the surface to inhibit corrosion
- C. Complete elimination pf the corrosion process
- D. Treating metal with a liquid inhibiter
Answer: A
NEW QUESTION # 53
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Synthetic oil or grease may not be identified
- B. Ultra-Violet light may contaminant the surface
- C. Presence of weld spatter may produce a false positive
- D. Chloride salt may produce a false positive
Answer: A
NEW QUESTION # 54
......
The salary of a NACE CIP1-001 certified professional can be found here.
The Average salary of different countries of NACE CIP1-001 Certified professionals is given below:
- India 4982421.50 INR
- USA 67,000 USD
- UK 49527.40 Pounds
Updated NACE-CIP1-001 Dumps Questions For NACE Exam: https://www.prep4pass.com/NACE-CIP1-001_exam-braindumps.html
Best Value Available Preparation Guide for NACE-CIP1-001 Exam: https://drive.google.com/open?id=1kxYSPo1u-hfW6yPrpm6b8OM8fxTRRyoB
