[Nov-2024] Pass NACE NACE-CIP1-001 Exam in First Attempt Guaranteed!
Full NACE-CIP1-001 Practice Test and 100 unique questions with explanations waiting just for you, get it now!
NEW QUESTION # 30
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- C. Document the problem and advise the Contractor and Owner's representative
- D. Document the problem and advise the Contractor
Answer: C
NEW QUESTION # 31
ISO SA 2.5 is defined as:
- A. Very Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Thorough Blast Cleaning
- D. Light Blast Cleaning
Answer: A
NEW QUESTION # 32
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Hand tools
- B. Airless spray equipment
- C. Abrasive blast nozzles
- D. Power tools
Answer: D
NEW QUESTION # 33
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION # 34
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. commercial blast cleaning.
- B. near-white metal blast cleaning.
- C. brush-off blast cleaning.
- D. white metal blast cleaning.
Answer: C
NEW QUESTION # 35
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. Yes, because the 'two standards are not equivalent
- C. No, because there is no real difference in the standards
- D. It depends on which hand tool the Contractor selects
Answer: C
NEW QUESTION # 36
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. All types of inspection
- C. Visual inspection and Non-destructive testing
- D. Visual inspection only
Answer: C
NEW QUESTION # 37
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. Organic solvents
- C. A wide variety of materials
- D. Biodegradable detergents
Answer: C
NEW QUESTION # 38
Upon arrival of coating materials, the inspector should
- A. observe aryl document that the applicator WFT at regular intervals during application.
- B. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- C. observe and document time frame and environmental conditions between each coat.
- D. observe and document the amount of material and batch numbers.
Answer: D
NEW QUESTION # 39
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 2/SSPC SP 10
- C. NACE No. 1/SSPC SP 5
- D. NACE No. 3/SSPC SP 6
Answer: A
NEW QUESTION # 40
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The Inspector will improve job flow and schedule
- C. The inspection cost will be offset by an improvement in service life
- D. a) and c)
Answer: D
NEW QUESTION # 41
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. NACE SP 0188
- B. NACE SP 0178
- C. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- D. SSPC PA 2
Answer: C
NEW QUESTION # 42
The NACE Inspector should perform tests for soluble salts:
- A. Prior to coating application
- B. After surface preparation
- C. Prior to surface preparation
- D. When specified
Answer: D
NEW QUESTION # 43
Polymerization is the process of:
- A. Monomers joining together
- B. Monomers telegraphing
- C. All organic coatings
- D. All thermoplastic coatings
Answer: A
NEW QUESTION # 44
The most important factor resulting in improved job site safety is:
- A. Engineering Controls
- B. Situational Awareness
- C. Safety Enforcement
- D. Personal Protective Equipment
Answer: B
NEW QUESTION # 45
......
Prepare for your NACE certification with the updated Prep4pass NACE-CIP1-001 exam questions: https://drive.google.com/open?id=1iKR5_nO37VGH7nNIhqsbs7i8X7de2vT7
Get Latest NACE-CIP1-001 Dumps Exam Questions in here: https://www.prep4pass.com/NACE-CIP1-001_exam-braindumps.html
