View All NACE-CIP1-001 Actual Exam Questions, Answers and Explanations for Free
NACE-CIP1-001 Exam Free Practice Test with100% Accurate Answers
NEW QUESTION # 37
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Taking measurements too far from the edge of a surface
- C. Measuring ditty, tacky, or soft films
- D. Failing to determine the base metal reading (BMR)
Answer: A,C,D
NEW QUESTION # 38
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Assume the role of the Safety Inspector
- B. Check the PPE used by the Applicators
- C. Check the credentials of the Safety Officer on site
- D. Act in accordance with the site safety requirements and set an example
Answer: D
NEW QUESTION # 39
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Conditions E-G
- B. Surface Condition H
- C. Rust Grades A-D
- D. Rust Grades 1-4
Answer: C
NEW QUESTION # 40
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept the assignment without hesitation
- B. Advise the prospective employer that you cannot accept the position
- C. Review the NACE Attestation prior to making a decision
- D. Meet with the prospective employer to determine the scope of your role
Answer: D
NEW QUESTION # 41
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Relative Humidity
- C. Low Relative Humidity
- D. High Surface Temperature
Answer: C
NEW QUESTION # 42
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Always handwritten
- C. Submitted before the end of the job
- D. Always typewritten
Answer: A
NEW QUESTION # 43
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Document the problem and advise the Contractor
- C. Document the problem and advise the Contractor and Owner's representative
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: C
NEW QUESTION # 44
Inspection documentation is important because:
- A. It is the only deliverable item provided by the inspector
- B. Owners use the documentation for a variety of purposes
- C. a) only
- D. a) & b)
Answer: B
NEW QUESTION # 45
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to, be Lined for Immersion Service
- B. Stainless steel pipe to be Externally Coated
- C. Structural steel to be coated for Atmospheric Service
- D. Tanks and Vessels to be Externally Coated
Answer: A
NEW QUESTION # 46
Safety Data Sheets must be carefully reviewed by:
- A. The Owner's personnel
- B. The Application personnel
- C. The Inspection personnel
- D. All personnel involved in the job
Answer: D
NEW QUESTION # 47
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION # 48
Check abrasive blast pressure close to the
- A. blast nozzle
- B. blast pot
- C. substrate
- D. compressor
Answer: A
NEW QUESTION # 49
Whenever dissimilar metals must join, the most common practice is to
- A. provide cathodic protection to prevent corrosion,
- B. avoid coating all connected dissimilar metals.
- C. coat all connected dissimilar metals.
- D. provide anodic protection to prevent corrosion.
Answer: C
NEW QUESTION # 50
ISO SA 2 is defined as:
- A. Thorough Blast Cleaning
- B. Very Thorough Blast Cleaning
- C. Light Blast Cleaning
- D. Near White Metal Blasting
Answer: A
NEW QUESTION # 51
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Owner's Representative
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. The Inspector should never transport coating material
- D. Asked to do so by the Coating Application team
Answer: C
NEW QUESTION # 52
A successful coating inspector must be able to
- A. apply the coating with expert accuracy.
- B. look for problems or issues during application.
- C. recommend the appropriate coating technique for the job to the contractor.
- D. advise the coating applicator on how to mix the coating.
Answer: B
NEW QUESTION # 53
Galvanic corrosion occurs on which of the following substrates:
- A. Wood
- B. Fiberglass Reinforced Plastic
- C. Concrete
- D. Metal
Answer: D
NEW QUESTION # 54
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Presence of weld spatter may produce a false positive
- B. Chloride salt may produce a false positive
- C. Ultra-Violet light may contaminant the surface
- D. Synthetic oil or grease may not be identified
Answer: D
NEW QUESTION # 55
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Inspector is convinced by verifiable facts
- C. The Inspectors position is not the majority position
- D. The Owner can save some money by the change
Answer: B
NEW QUESTION # 56
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. Yes, because the 'two standards are not equivalent
- B. No, because there is no real difference in the standards
- C. It depends on which power tool the Contractor selects
- D. It depends on which hand tool the Contractor selects
Answer: B
NEW QUESTION # 57
Stripe coats are best applied by:
- A. Conventional spray
- B. Airless spray
- C. Brush
- D. High volume low pressure spray
Answer: C
NEW QUESTION # 58
Upon arrival of coating materials, the inspector should
- A. observe and document time frame and environmental conditions between each coat.
- B. observe and document the amount of material and batch numbers.
- C. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- D. observe aryl document that the applicator WFT at regular intervals during application.
Answer: B
NEW QUESTION # 59
......
NACE-CIP1-001 dumps Free Test Engine Verified By It Certified Experts: https://www.prep4pass.com/NACE-CIP1-001_exam-braindumps.html
Realistic NACE-CIP1-001 Accurate & Verified Answers As Experienced in the Actual Test!: https://drive.google.com/open?id=1Hgk29t1rm1oVsAe8NhXdossFvqi4uQwX
